<!-- EP-133 K.O. II MIDI, measured: transport, notes, CC, velocity · https://getpadwork.app/howto/midi-facts -->
[Padwork](https://getpadwork.app/) › [How-to](https://getpadwork.app/howto/) › MIDI, measured

# EP-133 K.O. II MIDI: what it actually sends and takes

Measured on a 128 MB EP-133 K.O. II running OS 2.5.1, connected over USB, by logging its MIDI output and recording its USB audio. Nothing here comes from the manual unless it says so. Other firmware versions may differ.

**In short:** PLAY sends Song Position 0 + Continue, never Start. STOP sends Stop + CC 120. Pads send notes only with their own MIDI channel (or under code 110). CC 12/13 move the FX only under 110. The device sends no CC for its own knobs.

## Transport and clock

- PLAY sends Song Position Pointer 0 followed by Continue (F2 00 00, FB). It never sends Start (FA). The next clock pulse is that position.

- STOP sends Stop (FC) and then CC 120 (All Sound Off) on channels 1 to 12.

- MIDI clock out is a setting: SHIFT+ERASE 102 ENTER (100 = clock off, 101 = clock in). With it on, the EP-133 sends clock all the time, also while stopped.

- Picking a pattern on the device (hold the group button, press a number) sends nothing over MIDI. The change is in the project file only.

## Notes

- A pad on MIDI channel "default" sends no notes and plays none from incoming MIDI.

- A pad with its own channel sends its root note on that channel when hit, and plays any incoming note on that channel pitched relative to its root (note minus root, in semitones). Pads sharing a channel play together. Details and the system setting (codes 110 to 127) are on the [MIDI channels](https://getpadwork.app/howto/midi-channels) page.

- The sequencer sends each pad's recorded pitch on that pad's channel, so a pattern of 10 pad hits comes out as 10 notes on that pad's channel.

- While recording, the only traffic is notes and clock: no file events.

## Control changes

### CC 12 / 13 under 127 OFF
- Change nothing (measured 24 October and 5 November 2026, delay effect on).

### CC 12 / 13 under 110 ALL
- Move the FX knobs X and Y, as teenage engineering's guide says. Details: [Control the EP-133 FX over MIDI](https://getpadwork.app/howto/fx-midi-cc).

- The device sends no CC when you turn its knobs or move its fader. Those moves reach the project file seconds later (probed on 27 September 2026), so software can only follow them by re-reading the project.

## Velocity

With velocity mode on, three light, three medium and three hard taps per key, all in the middle of the key, gave these MIDI velocities on one unit:

| Key | Light | Medium | Hard |
| --- | --- | --- | --- |
| 5 (center) | 57 to 65 | 76 to 84 | 101 to 117 |
| 2 | 52 to 59 | 65 to 67 (one 114) | 127 |
| . (bottom left) | 55 to 57 | 57 to 58 (one 88) | 122 to 127 |
| 0 (bottom middle) | 56 to 62 | 65 to 70 | 97 to 113 |
| E (bottom right) | 55 to 61 | 54 to 63 | 121 to 126 |

The floor is the same everywhere (about 55). On the bottom corners a medium tap barely moves above it and then jumps close to the top; the center key has the smoothest range. Pressing 0 near its top edge didn't help (light 47 to 59, medium 57 to 70). Small sample and human fingers, but it looks like how the keys are built rather than a faulty unit.

## File transfers (SysEx) and sound

- Every file transfer over SysEx (reading a project or a sound) mutes the pads you hit on the device while it runs; the computer icon blinks. Playback from the sequencer is not interrupted: the USB audio during three full project reads measured the same as the bars before and after.

- Reading a whole project takes under a second. After it, the device ignores its buttons for 3 seconds: see [PLAY and STOP respond late](https://getpadwork.app/howto/buttons-late).

- A pattern you record is in the project file within 1.3 seconds after STOP.

- While a sound is being read, PLAY and STOP take effect seconds late. Once the read is over, STOP to silence measured 0.06 s.

- Switching project on the device (hold MAIN and a pad) sends no event; software only sees it by reading the active project.

## Not measured yet

System MIDI codes 111 to 126 in practice, the EP-40, firmware other than 2.5.1, and note-offs from the sequencer. If you have measured any of these, write to [support@getpadwork.app](mailto:support@getpadwork.app).

These measurements come from building [Padwork](https://getpadwork.app/), a free browser app for the EP-133.

Last checked: 6 November 2026, OS 2.5.1
